Jeep Vehicle Models Commander 2006-2010
Jeep Vehicle Models Commander 2006-2010 Torque Specifications
Complete Jeep Vehicle Models Commander 2006-2010 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
3.7l Engine
Torque specifications for 3.7L Engine
3.7l Engine
Torque specifications for 3.7L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 90°
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force and prevent warping.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure rocker arms are properly seated before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure proper crankshaft alignment.
2 Connecting Rod Nuts
M9 x 1.0
2
Connecting Rod Nuts
M9 x 1.0
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure connecting rods are properly seated on the crankshaft.
Timing System
1 Camshaft Sprocket Bolt
M10 x 1.25
1
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the timing marks are aligned before tightening.
2 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
2
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
Intake And Exhaust
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Follow the manufacturer's torque sequence to prevent warping.
2 Exhaust Manifold/Headers Bolts
M8 x 1.25
2
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the exhaust manifold is properly seated before tightening.
Lubrication System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2 Oil Drain Plug Bolt
M14 x 1.5
2
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Replace the crush washer to prevent leaks.
3.7l V6 Engine
Torque specifications for 3.7L-V6 Engine
3.7l V6 Engine
Torque specifications for 3.7L-V6 Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 90°
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force and prevent warping.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure rocker arms are properly seated before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure proper crankshaft alignment.
2 Connecting Rod Nuts
M9 x 1.0
2
Connecting Rod Nuts
M9 x 1.0
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure connecting rods are properly seated on the crankshaft.
Timing System
1 Camshaft Sprocket Bolt
M10 x 1.25
1
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the timing marks are aligned before tightening.
2 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
2
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
Intake And Exhaust
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Follow the manufacturer's torque sequence to prevent warping.
2 Exhaust Manifold/Headers Bolts
M8 x 1.25
2
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the exhaust manifold is properly seated before tightening.
Lubrication System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2 Oil Drain Plug Bolt
M14 x 1.5
2
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Replace the crush washer to prevent leaks.
4.7l Engine
Torque specifications for 4.7L Engine
4.7l Engine
Torque specifications for 4.7L Engine
Cylinder Head and Valvetrain
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Rocker Arms/Shafts Bolts
M10 x 1.25
2
Rocker Arms/Shafts Bolts
M10 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
3 Spark Plugs
M14 x 1.25
3
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Engine Block and Mounting
1 Engine Block to Transmission Mounting Bolts
M16 x 1.5
1
Engine Block to Transmission Mounting Bolts
M16 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Estimated value based on general industry standards.
2 Engine Block to Engine Mounting Bolts
M16 x 1.5
2
Engine Block to Engine Mounting Bolts
M16 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Estimated value based on general industry standards.
Crankshaft and Camshaft
1 Main Bearing Bolts
M18 x 1.5
1
Main Bearing Bolts
M18 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
2 Crankshaft Pulley/Harmonic Balancer Bolt
M20 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M20 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
3 Camshaft Sprocket Bolt
M14 x 1.25
3
Camshaft Sprocket Bolt
M14 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Intake and Exhaust
1 Intake Manifold Bolts
M10 x 1.25
1
Intake Manifold Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Exhaust Manifold/Headers Bolts
M12 x 1.5
2
Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Fuel and Ignition
1 Fuel Rail Bolts
M10 x 1.25
1
Fuel Rail Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Ignition Coil Bolt
M10 x 1.25
2
Ignition Coil Bolt
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
Cooling and Lubrication
1 Water Pump Bolts
M10 x 1.25
1
Water Pump Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Oil Filter Housing Bolt
M10 x 1.25
2
Oil Filter Housing Bolt
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
4.7l V8 Engine
Torque specifications for 4.7L-V8 Engine
4.7l V8 Engine
Torque specifications for 4.7L-V8 Engine
Cylinder Head and Valvetrain
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Rocker Arms/Shafts Bolts
M10 x 1.25
2
Rocker Arms/Shafts Bolts
M10 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
3 Spark Plugs
M14 x 1.25
3
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Engine Block and Mounting
1 Engine Block to Transmission Mounting Bolts
M16 x 1.5
1
Engine Block to Transmission Mounting Bolts
M16 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Estimated value based on general industry standards.
2 Engine Block to Engine Mounting Bolts
M16 x 1.5
2
Engine Block to Engine Mounting Bolts
M16 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Estimated value based on general industry standards.
Crankshaft and Camshaft
1 Main Bearing Bolts
M18 x 1.5
1
Main Bearing Bolts
M18 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
2 Crankshaft Pulley/Harmonic Balancer Bolt
M20 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M20 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
3 Camshaft Sprocket Bolt
M14 x 1.25
3
Camshaft Sprocket Bolt
M14 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Intake and Exhaust
1 Intake Manifold Bolts
M10 x 1.25
1
Intake Manifold Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Exhaust Manifold/Headers Bolts
M12 x 1.5
2
Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Fuel and Ignition
1 Fuel Rail Bolts
M10 x 1.25
1
Fuel Rail Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Ignition Coil Bolt
M10 x 1.25
2
Ignition Coil Bolt
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
Cooling and Lubrication
1 Water Pump Bolts
M10 x 1.25
1
Water Pump Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Oil Filter Housing Bolt
M10 x 1.25
2
Oil Filter Housing Bolt
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
5.7l Engine
Torque specifications for 5.7L Engine
5.7l Engine
Torque specifications for 5.7L Engine
Cylinder Head and Engine Block
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Cylinder Head Studs
M10 x 1.25
2
Cylinder Head Studs
M10 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on industry standards.
Main Bearings and Crankshaft
1 Main Bearing Bolts
M14 x 1.5
1
Main Bearing Bolts
M14 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
2 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Connecting Rods and Pistons
1 Connecting Rod Nuts
M10 x 1.25
1
Connecting Rod Nuts
M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Valve Train and Timing System
1 Camshaft Sprocket Bolt
M12 x 1.5
1
Camshaft Sprocket Bolt
M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
2 Timing Belt/Chain Tensioner Bolt
M10 x 1.25
2
Timing Belt/Chain Tensioner Bolt
M10 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Intake and Exhaust System
1 Intake Manifold Bolts
M10 x 1.25
1
Intake Manifold Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Exhaust Manifold/Headers Bolts
M10 x 1.25
2
Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Fuel System
1 Fuel Rail Bolts
M10 x 1.25
1
Fuel Rail Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Fuel Injector Bolts
M10 x 1.25
2
Fuel Injector Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
Cooling System
1 Water Pump Bolts
M10 x 1.25
1
Water Pump Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Water Pump Pulley Bolts
M10 x 1.25
2
Water Pump Pulley Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
Engine Mounts and Transmission
1 Engine Mounting Bolts
M12 x 1.5
1
Engine Mounting Bolts
M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on industry standards.
2 Engine Block to Transmission Bellhousing Bolts
M14 x 1.5
2
Engine Block to Transmission Bellhousing Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on industry standards.
5.7l V8 Engine
Torque specifications for 5.7L-V8 Engine
5.7l V8 Engine
Torque specifications for 5.7L-V8 Engine
Cylinder Head and Engine Block
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Cylinder Head Studs
M10 x 1.25
2
Cylinder Head Studs
M10 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on industry standards.
Main Bearings and Crankshaft
1 Main Bearing Bolts
M14 x 1.5
1
Main Bearing Bolts
M14 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
2 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Connecting Rods and Pistons
1 Connecting Rod Nuts
M10 x 1.25
1
Connecting Rod Nuts
M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Valve Train and Timing System
1 Camshaft Sprocket Bolt
M12 x 1.5
1
Camshaft Sprocket Bolt
M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
2 Timing Belt/Chain Tensioner Bolt
M10 x 1.25
2
Timing Belt/Chain Tensioner Bolt
M10 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Intake and Exhaust System
1 Intake Manifold Bolts
M10 x 1.25
1
Intake Manifold Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Exhaust Manifold/Headers Bolts
M10 x 1.25
2
Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Fuel System
1 Fuel Rail Bolts
M10 x 1.25
1
Fuel Rail Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Fuel Injector Bolts
M10 x 1.25
2
Fuel Injector Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
Cooling System
1 Water Pump Bolts
M10 x 1.25
1
Water Pump Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Water Pump Pulley Bolts
M10 x 1.25
2
Water Pump Pulley Bolts
M10 x 1.25
Torque Specification
105 in-lbs (12 N·m)
Engine Mounts and Transmission
1 Engine Mounting Bolts
M12 x 1.5
1
Engine Mounting Bolts
M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on industry standards.
2 Engine Block to Transmission Bellhousing Bolts
M14 x 1.5
2
Engine Block to Transmission Bellhousing Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on industry standards.
545rfe Transmission
Torque specifications for 545rfe Transmission
545rfe Transmission
Torque specifications for 545rfe Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M14 x 1.5
1
Transmission Mounting Bolts
M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Transmission Oil Pan
1 Transmission Oil Pan Bolts
M10 x 1.25
1
Transmission Oil Pan Bolts
M10 x 1.25
Torque Specification
7.3 ft-lbs (12 N·m)
Important Notes
Estimated value based on similar components and bolt sizes.
Transmission Drain and Fill
1 Transmission Drain and Fill Plugs
M12 x 1.5
1
Transmission Drain and Fill Plugs
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Torque Converter
1 Torque Converter Bolts
M14 x 1.5
1
Torque Converter Bolts
M14 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on industry standards.
Transmission Cooler Lines
1 Transmission Cooler Line Fittings
M12 x 1.5
1
Transmission Cooler Line Fittings
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on industry standards.
Transmission Pan Gasket
1 Transmission Pan Gasket Bolts
M10 x 1.25
1
Transmission Pan Gasket Bolts
M10 x 1.25
Torque Specification
7.3 ft-lbs (10 N·m)
Important Notes
Estimated value based on industry standards.
Body
Torque specifications for Body
Body
Torque specifications for Body
Fuel System
1 Fuel Tank Strap Bolts
M8 x 1.25
1
Fuel Tank Strap Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the fuel tank is properly aligned before tightening.
2 Fuel Filler Neck Bolts
M6 x 1.0
2
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the filler neck is properly aligned with the fuel tank.
Safety System
1 Seat Belt Anchorage Bolts
M10 x 1.5
1
Seat Belt Anchorage Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on similar safety-critical components.
2 Seat Mounting Bolts
M10 x 1.5
2
Seat Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on similar safety-critical components.
Body Panels
1 Door Hinge Bolts
M8 x 1.25
1
Door Hinge Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on similar hinge applications.
2 Bumper Mounting Bolts
M8 x 1.25
2
Bumper Mounting Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on similar structural components.
3 Body Panel Bolts
M6 x 1.0
3
Body Panel Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Estimated value based on similar panel fasteners.
Electrical System
1 Battery Terminal Nuts
M6 x 1.0
1
Battery Terminal Nuts
M6 x 1.0
Torque Specification
5.42 ft-lbs (7 N·m)
Important Notes
Ensure the battery terminals are clean and free of corrosion before tightening.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Brake Caliper
1 Brake Caliper Bolts
M10 x 1.5
1
Brake Caliper Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the brake caliper to the mounting bracket. Proper torque ensures the caliper is securely attached.
2 Brake Caliper Mounting Bracket Bolts
M12 x 1.5
2
Brake Caliper Mounting Bracket Bolts
M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Attaches the caliper mounting bracket to the steering knuckle or axle. Proper torque ensures the bracket is firmly secured.
Brake Disc Drum
1 Brake Disc/Drum Retaining Bolts
M8 x 1.25
1
Brake Disc/Drum Retaining Bolts
M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Holds the brake disc or drum to the wheel hub. Proper torque ensures the disc/drum remains securely in place.
Brake Hydraulics
1 Brake Hose Banjo Bolt
M8 x 1.25
1
Brake Hose Banjo Bolt
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Connects the brake hose to the caliper or brake line. Proper torque ensures a leak-free connection.
Brake Master Cylinder
1 Brake Master Cylinder Mounting Bolts
M8 x 1.25
1
Brake Master Cylinder Mounting Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Secures the master cylinder to the brake booster. Proper torque ensures the master cylinder is firmly attached.
Brake Booster
1 Brake Booster Mounting Bolts
M8 x 1.25
1
Brake Booster Mounting Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the brake booster to the firewall. Proper torque ensures the booster is firmly attached.
Brake Pedal
1 Brake Pedal Assembly Bolts
M8 x 1.25
1
Brake Pedal Assembly Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the brake pedal assembly to the firewall or pedal bracket. Proper torque ensures the pedal operates smoothly.
Wheel Assembly
1 Wheel Lug Nuts
M12 x 1.5
1
Wheel Lug Nuts
M12 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Secures the wheel to the hub. Proper torque is critical for ensuring the wheel is firmly attached, which directly affects brake performance and safety.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine and Transmission
1 Flywheel Bolts
M14 x 1.5
1
Flywheel Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
2 Transmission Mounting Bolts
M12 x 1.25
2
Transmission Mounting Bolts
M12 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
3 Main Bearing Bolts
M16 x 1.5
3
Main Bearing Bolts
M16 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
4 Crankshaft Pulley/Harmonic Balancer Bolt
M18 x 1.5
4
Crankshaft Pulley/Harmonic Balancer Bolt
M18 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Transmission and Driveshaft
1 Transmission Oil Pan Bolts
M10 x 1.25
1
Transmission Oil Pan Bolts
M10 x 1.25
Torque Specification
105 ft-lbs (12 N·m)
Important Notes
Estimated value, consult service manual for specific torque value.
2 Propeller/Drive Shaft Bolts
M14 x 1.5
2
Propeller/Drive Shaft Bolts
M14 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
3 Driveshaft Universal Joint Bolts
M12 x 1.25
3
Driveshaft Universal Joint Bolts
M12 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Estimated value, consult service manual for specific torque value.
Axles and Hubs
1 Drive Axle/Half Shaft Bolts
M14 x 1.5
1
Drive Axle/Half Shaft Bolts
M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
2 CV Joint/Axle Nut
M20 x 1.5
2
CV Joint/Axle Nut
M20 x 1.5
Torque Specification
180 ft-lbs (244 N·m)
3 Front and Rear Axle Hub Nuts
M18 x 1.5
3
Front and Rear Axle Hub Nuts
M18 x 1.5
Torque Specification
120 ft-lbs (163 N·m)
Important Notes
Estimated value, consult service manual for specific torque value.
Differential and Transfer Case
1 Differential Carrier Bolts
M16 x 1.5
1
Differential Carrier Bolts
M16 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Estimated value, consult service manual for specific torque value.
2 Transfer Case Mounting Bolts
M14 x 1.5
2
Transfer Case Mounting Bolts
M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Estimated value, consult service manual for specific torque value.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Alternator And Starter Motor
1 Alternator Mounting Bolts
M12 x 1.5
1
Alternator Mounting Bolts
M12 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
2 Starter Motor Mounting Bolts
M12 x 1.5
2
Starter Motor Mounting Bolts
M12 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Battery Terminals
1 Battery Terminal Nuts
M8 x 1.25
1
Battery Terminal Nuts
M8 x 1.25
Torque Specification
65 in-lbs (7 N·m)
Ignition Coil And Spark Plug Wires
1 Ignition Coil Mounting Bolts
M10 x 1.5
1
Ignition Coil Mounting Bolts
M10 x 1.5
Torque Specification
1. 10 ft-lbs (14 N·m)
2. 15 ft-lbs (20 N·m)
Important Notes
Estimated torque values based on general industry guidelines.
2 Spark Plug Wire Boots
M8 x 1.25
2
Spark Plug Wire Boots
M8 x 1.25
Torque Specification
1. 10 ft-lbs (14 N·m)
2. 15 ft-lbs (20 N·m)
Important Notes
Estimated torque values based on general industry guidelines.
Fuel Pump Electrical Connector
1 Fuel Pump Electrical Connector Bolts
M6 x 1.0
1
Fuel Pump Electrical Connector Bolts
M6 x 1.0
Torque Specification
1. 5 ft-lbs (7 N·m)
2. 10 ft-lbs (14 N·m)
Important Notes
Estimated torque values based on general industry guidelines.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Exhaust System
1 Exhaust Manifold/Headers Bolts
M12 x 1.5
1
Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Catalytic Converter to Exhaust Pipe Bolts
M12 x 1.5
2
Catalytic Converter to Exhaust Pipe Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
EGR System
1 EGR Valve Bolts
M10 x 1.25
1
EGR Valve Bolts
M10 x 1.25
Torque Specification
17 ft-lbs (23 N·m)
2 EGR Cooler Bolts
M12 x 1.5
2
EGR Cooler Bolts
M12 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 30 ft-lbs (41 N·m)
Important Notes
Estimated torque range due to lack of specific data.
Oxygen Sensors
1 Oxygen Sensor Bolts
M12 x 1.5
1
Oxygen Sensor Bolts
M12 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 20 ft-lbs (27 N·m)
Important Notes
Estimated torque range due to lack of specific data.
2 Heated Oxygen Sensor (HO2S) Bolts
M12 x 1.5
2
Heated Oxygen Sensor (HO2S) Bolts
M12 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 20 ft-lbs (27 N·m)
Important Notes
Estimated torque range due to lack of specific data.
3 NOx Sensor Bolts
M12 x 1.5
3
NOx Sensor Bolts
M12 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 20 ft-lbs (27 N·m)
Important Notes
Estimated torque range due to lack of specific data.
Diesel Particulate Filter (DPF)
1 DPF Bolts
M12 x 1.5
1
DPF Bolts
M12 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 30 ft-lbs (41 N·m)
Important Notes
Estimated torque range due to lack of specific data.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold Headers
1 Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
1
Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M8 x 1.25
2
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure a secure connection to prevent leaks at this critical junction.
Catalytic Converter
1 Catalytic Converter to Exhaust Pipe Bolts
M8 x 1.25
1
Catalytic Converter to Exhaust Pipe Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure a secure connection to prevent leaks.
Muffler
1 Muffler to Exhaust Pipe Bolts
M8 x 1.25
1
Muffler to Exhaust Pipe Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure a secure connection to prevent leaks.
Exhaust Hangers
1 Exhaust Hanger Bolts
M6 x 1.0
1
Exhaust Hanger Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar components and bolt sizes.
Oxygen Sensors
1 Oxygen Sensor Bolts
M8 x 1.25
1
Oxygen Sensor Bolts
M8 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Estimated value based on similar components and bolt sizes.
Exhaust Flanges
1 Exhaust Flange Bolts
M8 x 1.25
1
Exhaust Flange Bolts
M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Estimated value based on similar components and bolt sizes.
Heat Shields
1 Heat Shield Bolts
M6 x 1.0
1
Heat Shield Bolts
M6 x 1.0
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Estimated value based on similar components and bolt sizes.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Rail System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure injectors are properly seated before tightening.
Fuel Pump And Tank System
1 Fuel Pump Mounting Bolts
M6 x 1.0
1
Fuel Pump Mounting Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the fuel pump gasket is properly seated before tightening.
2 Fuel Tank Strap Bolts
M10 x 1.5
2
Fuel Tank Strap Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the fuel tank is properly aligned before tightening.
3 Fuel Filler Neck Bolts
M6 x 1.0
3
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the filler neck gasket is properly seated.
4 Fuel Tank Sender Unit Bolts
M6 x 1.0
4
Fuel Tank Sender Unit Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Estimated value based on similar components. Ensure the sender unit gasket is properly seated.
Fuel Filter And Regulator System
1 Fuel Filter Bolt/Nut
M8 x 1.25
1
Fuel Filter Bolt/Nut
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the filter is properly aligned before tightening.
2 Fuel Pressure Regulator Bolts
M6 x 1.0
2
Fuel Pressure Regulator Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Estimated value based on similar components. Ensure the regulator is properly seated.
Fuel Line System
1 Fuel Line Fittings
M10 x 1.5
1
Fuel Line Fittings
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure fittings are properly aligned and seated before tightening.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Ac Compressor
1 A/C Compressor Mounting Bolts
M10 x 1.5
1
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N-m)
Important Notes
Ensure the compressor is properly aligned before tightening. Torque values are estimated based on typical A/C compressor applications.
2 A/C Line Fittings
M8 x 1.25
2
A/C Line Fittings
M8 x 1.25
Torque Specification
25 ft-lbs (34 N-m)
Important Notes
Ensure fittings are clean and free of debris before installation. Torque values are estimated based on typical refrigerant line applications.
Evaporator Core
1 Evaporator Core Housing Bolts
M6 x 1.0
1
Evaporator Core Housing Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N-m)
Important Notes
Torque values are estimated based on typical evaporator housing applications.
Blower Motor
1 Blower Motor Mounting Bolts
M6 x 1.0
1
Blower Motor Mounting Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N-m)
Important Notes
Torque values are estimated based on typical blower motor applications.
Heater Core
1 Heater Core Inlet/Outlet Fittings
M8 x 1.25
1
Heater Core Inlet/Outlet Fittings
M8 x 1.25
Torque Specification
25 ft-lbs (34 N-m)
Important Notes
Ensure fittings are clean and free of debris before installation. Torque values are estimated based on typical heater core applications.
Hvac Case
1 HVAC Case Assembly Bolts
M6 x 1.0
1
HVAC Case Assembly Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N-m)
Important Notes
Torque values are estimated based on typical HVAC case applications.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Strut and Shock Absorber Mounting
1 Strut/Shock Absorber Mounting Bolts
M14 x 1.5
1
Strut/Shock Absorber Mounting Bolts
M14 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Control Arm and Steering Components
1 Control Arm Bolts
M16 x 1.5
1
Control Arm Bolts
M16 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
2 Ball Joint Nut
M12 x 1.5
2
Ball Joint Nut
M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
3 Tie Rod End Nut
M12 x 1.5
3
Tie Rod End Nut
M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
4 Sway Bar Link Nut
M12 x 1.5
4
Sway Bar Link Nut
M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
5 Steering Gear/Rack Bolts
M14 x 1.5
5
Steering Gear/Rack Bolts
M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Control Arm Bushings and Coil Spring Isolators
1 Upper Control Arm Bushing Bolts
M10 x 1.5
1
Upper Control Arm Bushing Bolts
M10 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for correct torque value.
2 Lower Control Arm Bushing Bolts
M10 x 1.5
2
Lower Control Arm Bushing Bolts
M10 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for correct torque value.
3 Coil Spring Isolator Bolts
M8 x 1.25
3
Coil Spring Isolator Bolts
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for correct torque value.
Stabilizer Bar Mounting
1 Stabilizer Bar Mounting Bolts
M12 x 1.5
1
Stabilizer Bar Mounting Bolts
M12 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for correct torque value.
W5a580 Transmission
Torque specifications for W5a580 Transmission
W5a580 Transmission
Torque specifications for W5a580 Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M14 x 1.5
1
Transmission Mounting Bolts
M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Transmission Oil System
1 Transmission Oil Pan Bolts
M10 x 1.25
1
Transmission Oil Pan Bolts
M10 x 1.25
Torque Specification
8.5 ft-lbs (12 N·m)
2 Transmission Drain and Fill Plugs
M12 x 1.5
2
Transmission Drain and Fill Plugs
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
3 Transmission Fluid Drain/Fill Plug
M12 x 1.5
3
Transmission Fluid Drain/Fill Plug
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Transmission Case and Components
1 Transmission Case Bolts
M14 x 1.5
1
Transmission Case Bolts
M14 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Estimated value based on industry standards.
2 Valve Body Bolts
M10 x 1.25
2
Valve Body Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on industry standards.
3 Solenoid Pack Bolts
M6 x 1
3
Solenoid Pack Bolts
M6 x 1
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on industry standards.
4 Torque Converter Bolts
M14 x 1.5
4
Torque Converter Bolts
M14 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Estimated value based on industry standards.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the recommended torque setting for lug nuts on a 2008 Jeep Commander?
Q1
What IS the recommended torque setting for lug nuts on a 2008 Jeep Commander?
115 ft-lbs (157 Nm)
Q2 How do I properly torque the bolts on my Jeep Commander's cylinder head?
Q2
How do I properly torque the bolts on my Jeep Commander's cylinder head?
Follow these steps: 1. Clean and lubricate the threads on the bolts and in the cylinder head. 2. Tighten the bolts to 22 ft-lbs (30 Nm) in three stages. 3. Use a torque wrench to achieve the final tightening torque of 61 ft-lbs (83 Nm).
Q3 What tools do I need to torque bolts correctly?
Q3
What tools do I need to torque bolts correctly?
You will need a torque wrench, a socket wrench, and the appropriate sockets for the bolts you are tightening.
Q4 Why IS it important to follow the specified torque settings?
Q4
Why IS it important to follow the specified torque settings?
Proper torque settings ensure that the bolts are tightened to the correct tension, which IS critical for the safety and performance of the vehicle.
Q5 What are the consequences of over-tightening or under-tightening bolts?
Q5
What are the consequences of over-tightening or under-tightening bolts?
Over-tightening can damage the threads or strip the bolt, while under-tightening can cause the bolt to loosen and fail.
Q6 Where can I find the torque specifications for my specific Jeep Commander model?
Q6
Where can I find the torque specifications for my specific Jeep Commander model?
Refer to your vehicle's service manual or contact an authorized Jeep dealer for the most accurate and up-to-date torque specifications.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the commander.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Bolt Torque Specifications for 2006-2010 Jeep Commander
Comprehensive guide to bolt torque specifications for various components on the Jeep Commander
- Locate the specific component and identify the corresponding bolt size and grade.
- Refer to the table below for the appropriate torque specification in Nm or ft-lb.
- Use a digital torque wrench to tighten the bolt to the specified torque, ensuring a secure and properly assembled component.
- Torque values are critical for maintaining structural integrity and preventing damage or failure.
Technical Service Bulletins
Bolt Torque Specification Update for 2006-2010 Jeep Commander
2015-04-01Revised bolt torque specifications for certain components on the Jeep Commander to address potential issues
2006-2010 commander
Resolution: Follow the updated torque specifications as outlined in the bulletin to ensure proper tightening and avoid component failure.
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.