Jeep Vehicle Models Compass 2007-2016 Torque Specifications
Jeep Vehicle Models Compass 2007-2016

Jeep Vehicle Models Compass 2007-2016 Torque Specifications

Complete Jeep Vehicle Models Compass 2007-2016 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

2.0l I4 Engine

Torque specifications for 2.0L-I4 Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90°
Important Notes
Follow the manufacturer's torque sequence to prevent warping.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.
3

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure rocker arms are properly aligned before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
58 ft-lbs (79 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
2

Connecting Rod Nuts

M9 x 1.0
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure connecting rods are properly aligned before tightening.
3

Flywheel Bolts

M12 x 1.75
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Use thread locker on flywheel bolts to prevent loosening.

Timing System

1

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the timing marks are aligned before tightening.
2

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
20.8 ft-lbs (28 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
10.4 ft-lbs (14 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Replace the crush washer to ensure a proper seal.

2.4l I4 Engine

Torque specifications for 2.4L-I4 Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to prevent warping or gasket failure.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.5
Torque Specification
58 ft-lbs (79 N·m)
Important Notes
Ensure proper alignment of bearing caps before tightening.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of connecting rods before tightening.

Flywheel And Clutch

1

Flywheel Bolts

M10 x 1.25
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Use thread locker on bolt threads as specified by the manufacturer.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
10.4 ft-lbs (14 N·m)
Important Notes
Over-tightening can damage the oil pan or gasket.
2

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new crush washer to ensure a proper seal.

Valve Train

1

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure proper alignment of rocker arms before tightening.

Ignition System

1

Spark Plugs

M14 x 1.25
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Over-tightening can damage the threads or spark plugs.
2

Ignition Coil Bolt

M6 x 1.0
Torque Specification
5.9 ft-lbs (8 N·m)
Important Notes
Over-tightening can damage the ignition coil or mounting surface.

Body

Torque specifications for Body

Suspension System

1

Strut/Shock Absorber Mounting Bolts

M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secure the strut/shock absorber to the vehicle's body.
2

Control Arm Bolts

M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Attach the control arms to the vehicle's body.

Steering System

1

Steering Gear/Rack Bolts

M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Secure the steering gear/rack to the vehicle's body.

Brake System

1

Brake Caliper Bolts

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Attach the brake caliper to the vehicle's body.
2

Brake Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Secure the brake caliper mounting bracket to the vehicle's body.

Body Mounts

1

Body Mount Bolts

M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value. Secure the vehicle's body to the frame. Consult the vehicle's repair manual or manufacturer's documentation for accurate information.

Door Hinges

1

Door Hinge Bolts

M10 x 1.5
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Estimated value. Attach the doors to the vehicle's body. Consult the vehicle's repair manual or manufacturer's documentation for accurate information.

Hood Hinges

1

Hood Hinge Bolts

M10 x 1.5
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Estimated value. Attach the hood to the vehicle's body. Consult the vehicle's repair manual or manufacturer's documentation for accurate information.

Trunk Lid Hinges

1

Trunk Lid Hinge Bolts

M10 x 1.5
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Estimated value. Attach the trunk lid to the vehicle's body. Consult the vehicle's repair manual or manufacturer's documentation for accurate information.

Bumper Mounts

1

Bumper Mounting Bolts

M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value. Secure the bumper to the vehicle's body. Consult the vehicle's repair manual or manufacturer's documentation for accurate information.

Brakes

Torque specifications for Brakes

Brake Caliper System

1

Brake Caliper Bolts

M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the caliper is properly aligned before torquing.
2

Brake Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensure the bracket is properly seated against the steering knuckle or axle.

Brake Rotor Drum System

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the rotor or drum is properly seated against the hub.

Brake Hydraulic System

1

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the sealing washers are properly seated before torquing.
2

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the master cylinder is properly aligned with the brake booster.
3

Brake Booster Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the booster is properly seated against the firewall.

Brake Pedal System

1

Brake Pedal Assembly Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the pedal assembly is properly aligned with the master cylinder pushrod.

Wheel Attachment System

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Always use a torque wrench to ensure proper tightening. Over-torquing can damage the wheel studs.

Drivetrain

Torque specifications for Drivetrain

Engine and Transmission Interface

1

Flywheel Bolts

M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)

Transmission Mounting and Oil Pan

1

Transmission Mounting Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
2

Transmission Oil Pan Bolts

M8 x 1.25
Torque Specification
125 in-lbs (14 N·m)
Important Notes
Note: The torque value is specified in inch-pounds.

Drivetrain Axles and Shafts

1

Drive Axle/Half Shaft Bolts

M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
2

CV Joint/Axle Nut

M20 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
3

Propeller/Drive Shaft Bolts

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)

Differential and Transfer Case

1

Differential Drain/Fill Plug

M14 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
2

Transfer Case Drain/Fill Plug

M12 x 1.5
Torque Specification
29 ft-lbs (39 N·m)

Additional Components

1

Transmission Crossmember Bolts

M14 x 1.5
Torque Specification
60 ft-lbs (80 N·m)
Important Notes
Estimated value based on general industry standards.
2

Driveshaft Center Bearing Bolts

M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on general industry standards.
3

Axle Shaft Retaining Bolts

M12 x 1.5
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Estimated value based on general industry standards.
4

Differential Cover Bolts

M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on general industry standards.
5

Transfer Case Mounting Bolts

M12 x 1.5
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Estimated value based on general industry standards.

Electrical

Torque specifications for Electrical

Charging System

1

Alternator Mounting Bolts

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the alternator is properly aligned before tightening.
2

Battery Terminal Nuts

M6 x 1.0
Torque Specification
7.9 ft-lbs (11 N·m)
Important Notes
Ensure the terminals are clean and free of corrosion before tightening.

Starting System

1

Starter Motor Mounting Bolts

M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the starter motor is properly aligned before tightening.

Ignition System

1

Ignition Coil Mounting Bolts

M6 x 1.0
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Estimated value based on similar components. Ensure the ignition coil is properly seated before tightening.
2

Spark Plug Wire Retainer Bolts

M5 x 0.8
Torque Specification
7.5 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar components. Ensure the spark plug wires are properly routed before tightening.

Fuel System

1

Fuel Pump Electrical Connector Bolts

M5 x 0.8
Torque Specification
7.5 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar components. Ensure the electrical connector is properly seated before tightening.

Climate Control System

1

A/C Compressor Electrical Connector Bolts

M5 x 0.8
Torque Specification
7.5 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar components. Ensure the electrical connector is properly seated before tightening.

Emissions Sensors

Torque specifications for Emissions_sensors

Oxygen Sensors

1

Oxygen Sensor (O2 Sensor) Bolt

M12 x 1.5
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Estimated value based on industry standards. Actual value may vary depending on the specific vehicle and sensor manufacturer.
2

Heated Oxygen Sensor (HO2S) Bolt

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on industry standards. Actual value may vary depending on the specific vehicle and sensor manufacturer.

Exhaust Gas Recirculation (EGR) System

1

EGR Valve Bolts

M10 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Actual value may vary depending on the specific vehicle and EGR valve manufacturer.

Exhaust Gas Temperature (EGT) Sensor

1

EGT Sensor Bolt

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value based on industry standards. Actual value may vary depending on the specific vehicle and sensor manufacturer.

Mass Airflow (MAF) Sensor

1

MAF Sensor Bolt

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value based on industry standards. Actual value may vary depending on the specific vehicle and sensor manufacturer.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold Headers

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N-m)
Important Notes
Torque value is estimated based on similar components. Always follow the manufacturer's recommended sequence for tightening.
2

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N-m)
Important Notes
Torque value is estimated based on similar components.

Catalytic Converter

1

Catalytic Converter to Exhaust Pipe Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N-m)
Important Notes
Torque value is estimated based on similar components.

Muffler

1

Muffler to Exhaust Pipe Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N-m)
Important Notes
Torque value is estimated based on similar components.

Exhaust Hangers

1

Exhaust Hanger Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (25 N-m)
Important Notes
Torque value is estimated based on similar components.

Oxygen Sensors

1

Oxygen Sensor Bolts

M10 x 1.25
Torque Specification
30 ft-lbs (40 N-m)
Important Notes
Torque value is estimated based on similar components.

Heat Shields

1

Exhaust Heat Shield Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N-m)
Important Notes
Torque value is estimated based on similar components.

Exhaust Flanges

1

Exhaust Flange Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N-m)
Important Notes
Torque value is estimated based on similar components.

Fuel

Torque specifications for Fuel

Fuel Delivery

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7.42 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment of the fuel rail before tightening.
2

Fuel Injector Bolts

M5 x 0.8
Torque Specification
5.92 ft-lbs (8 N·m)
Important Notes
Ensure injectors are properly seated before tightening.
3

High-Pressure Fuel Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the pump is properly aligned with the engine block.
4

Fuel Pressure Regulator Bolts

M6 x 1.0
Torque Specification
7.42 ft-lbs (10 N·m)
Important Notes
Ensure the regulator is properly seated before tightening.

Fuel Storage

1

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the fuel pump assembly is properly seated in the tank.
2

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the fuel tank is properly aligned before tightening.
3

Fuel Tank Sender Unit Bolts

M6 x 1.0
Torque Specification
7.42 ft-lbs (10 N·m)
Important Notes
Ensure the sender unit is properly seated before tightening.

Fuel Filtration

1

Fuel Filter Bolt/Nut

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the fuel filter housing is properly aligned before tightening.

Fuel Filling

1

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the filler neck is properly aligned with the fuel tank or body.

Fuel Lines

1

Fuel Line Fittings

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure fittings are properly seated before tightening.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N-m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute load.
2

A/C Line Fittings

M8 x 1.25
Torque Specification
18 ft-lbs (25 N-m)
Important Notes
Ensure fittings are clean and free of debris before installation.

Evaporator Core

1

Evaporator Core Housing Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N-m)
Important Notes
Ensure the housing gasket is properly seated before tightening.

Blower Motor

1

Blower Motor Mounting Bolts

M5 x 0.8
Torque Specification
5.9 ft-lbs (8 N-m)
Important Notes
Ensure the blower motor is properly aligned with the housing.

Heater Core

1

Heater Core Inlet/Outlet Pipe Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N-m)
Important Notes
Ensure the O-rings or gaskets are properly seated before tightening.

Control Panel

1

HVAC Control Panel Mounting Screws

M4 x 0.7
Torque Specification
2.9 ft-lbs (4 N-m)
Important Notes
Ensure the control panel is properly aligned with the dashboard.

Jf011e Transmission

Torque specifications for Jf011e Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M8 x 1.25
Torque Specification
9 ft-lbs (14 N·m)
Important Notes
Note: The torque value is converted from 125 inch-lbs.

Transmission Fluid Drain and Fill

1

Transmission Fluid Drain and Fill Plugs

M18 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
2

Transmission Fluid Drain/Fill Plug

M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)

Transmission Case

1

Transmission Case Bolts

M14 x 1.5
Torque Specification
1. 60 ft-lbs (80 N·m) 2. 80 ft-lbs (110 N·m)
Important Notes
Note: The torque values are estimated based on general industry standards.

Transmission Bellhousing

1

Transmission Bellhousing Bolts

M12 x 1.5
Torque Specification
1. 40 ft-lbs (54 N·m) 2. 50 ft-lbs (68 N·m)
Important Notes
Note: The torque values are estimated based on general industry standards.

Transmission Crossmember

1

Transmission Crossmember Bolts

M14 x 1.5
Torque Specification
1. 40 ft-lbs (54 N·m) 2. 50 ft-lbs (68 N·m)
Important Notes
Note: The torque values are estimated based on general industry standards.

Torque Converter

1

Torque Converter Bolts

M10 x 1.25
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 40 ft-lbs (54 N·m)
Important Notes
Note: The torque values are estimated based on general industry standards.

Suspension

Torque specifications for Suspension

Strut/Shock Absorber Mounting

1

Strut/Shock Absorber Mounting Bolts

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)

Control Arm Assembly

1

Control Arm Bolts

M16 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
2

Upper Control Arm Bushing Bolts

M12 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value based on industry standards.
3

Lower Control Arm Bolts

M14 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Estimated value based on industry standards.

Steering and Suspension

1

Ball Joint Nut

M18 x 1.5
Torque Specification
61 ft-lbs (83 N·m)
2

Tie Rod End Nut

M14 x 1.5
Torque Specification
36 ft-lbs (49 N·m)
3

Sway Bar Link Nut

M12 x 1.25
Torque Specification
36 ft-lbs (49 N·m)
4

Steering Knuckle Bolts

M16 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Estimated value based on industry standards.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque for lug nuts on a 2007-2016 Jeep Compass?

Tighten lug nuts to 100 ft-lbs (136 Nm) using a torque wrench.

Q2

What IS the torque specification for the oil drain plug on a 2010 Jeep Compass?

Tighten the oil drain plug to 29 ft-lbs (39 Nm) using a torque wrench.

Q3

How much torque should be applied to the spark plugs on a 2014 Jeep Compass?

Tighten spark plugs to 20 ft-lbs (27 Nm) using a torque wrench.

Q4

What IS the correct torque for the brake caliper mounting bolts on a 2007 Jeep Compass?

Tighten brake caliper mounting bolts to 120 ft-lbs (163 Nm) using a torque wrench.

Q5

What tools are recommended for accurately applying torque specifications on a Jeep Compass?

Use a calibrated torque wrench with the appropriate socket for each bolt or nut. Refer to the owner's manual for specific torque wrench recommendations.

Q6

How can I ensure the accuracy of my torque measurements?

Calibrate your torque wrench regularly according to the manufacturer's instructions. Use a torque wrench that IS within its recommended range and handle it with care.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the Compass.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Tightening Wheel Lug Nuts

This procedure outlines the steps for properly tightening the wheel lug nuts on a 2007-2016 Jeep Compass.

  • Clean the lug nuts and threads on the wheel.
  • Apply a small amount of anti-seize lubricant to the lug nuts.
  • Install the lug nuts onto the wheel and hand-tighten them.
  • Use a torque wrench to tighten the lug nuts to the specified torque of 100 Nm (74 ft-lb).
  • Re-check the tightness of the lug nuts after 100 km (60 miles) of driving.
View full procedure
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Jeep Specs. All rights reserved.

Privacy Policy Terms of Service